Thursday 16 January 2014

DIY - Vacuum Bagging System


The "Smart Little Sucker"
With a few board designs in the pipeline it was time to upgrade my vacuum pump to a system with vacuum pressure control. Up until know I have used the cheap fridge pump option and while you may save a lot of money on the initial outlay you soon loose money if you damage a blank(or 2 as I did!!!!) using excessive vacuum pressure.  The vacuum pressure control is achieved by using a tee fitting with a ball valve in combination with a vacuum gauge. While this setup may be good for small bagging jobs and high vac pressures with robust moulds I have had problems bagging boards where the vacuum pressure is stable for several hours and then a leak or hole suddenly seals itself and the pressure goes throught the floor(really low ;). Since the vacuum has to be maintained for 12 hours or so this makes bagging overnight risky.

My old fridge pump system.

The pump was fan cooled on big jobs.

The next step up from using a ball valve is a diaphragm and reed switch but I am not a fan of this version due to the lack of precise control as well as questionable electrical safety.

I wanted precise vacuum control without the pump having to run continuously and came across this veneer vacuum system from Veneer Supplies.Com: http://www.veneersupplies.com/products/Project-EVS-Auto-Cycling-Pump-Vacuum-Press-Kit.html

I was able to scrounge most of the required components from the parts bin at work except for a vacuum controller. I decided to use an SMC electronic vacuum switch for accurate control and the hysteresis function to reduce frequent pump switching.

The need for a small footprint as well as portability meant than I had to stack the components using a plywood shelf system. This is the prototype which will probably stay this way - functional!

Working from the Air Fitting back there is a ball valve to isolate the system from the vacuum bagging line.  The ball valve is connected to the vacuum reservoirs(tubes of nothingness...) which are separated by a takeoff for the vacuum switch. 

Vacuum Reservoirs.

The reservoirs are then connected to a check valve(one way valve) to store the vacuum in the reservoirs.

Top view of Vacuum Reservoirs, Vacuum switch and Check Valve.
Connected to the check valve is a 3 way solenoid valve to relieve the vacuum pressure behind the check valve when the pump is switched off by the vacuum switch.  This stops the pump having the start under load. Next up is a under bench water filter which acts as both a line filter and sub reservoir.  The sub-reservoir allows the pump the run to full RPM without back pressure on the pump intake port. Connected to the filter is a small diaphragm pump which is oil free and super quiet when an exhaust muffler is fitted.

3 Way Valve, Sub-reservoir/Filter and Pump.
Below the pump is a small termination box housing the terminals, 24v Power Supply and Contactor.  The Vacuum switch outputs a signal to the contactor which switches off the pump and opens the exhaust valve at the desired vacuum pressure.

Terminals, Contactor and 24V P.S.
Next up is a test run on a new board or 2!

7 comments:

  1. Hi mate, how did you wire up the SMC switch? Is it a relay or an inline switch?

    ReplyDelete
  2. Hi Tim, I used a contactor instead of a relay as I was switching a motor with inrush.

    ReplyDelete
  3. wow!!!Nice Post.I know you took lots of effort to do this.

    ReplyDelete
  4. Frequent clean-up is additionally perfect for the earth mainly because fewer compounds are essential to help keep this costly sense of balance. When a pool area has a pile-up connected with dust in addition to obtains outside of sense of balance lots of element is usually gain some sort of protected setting all over again. website PressureWasherGuides.com

    ReplyDelete
  5. Most pool owners understand the differences between a swimming pool heater and heat pump. However, when it comes to heat pumps, pool owners are especially curious about which swimming pool heat pump is best? Are Raypak heat pumps more reliable than the Pentair heat pumps? Or, does the manufacturer not play a huge deciding factor?

    In this blog article, we compare some of the best heat pumps for swimming pools in hopes of narrowing down which unit is best for your pool.

    ReplyDelete
  6. There are many simple ways to use tanks for liquid oxygen. Your oxygen equipment, including tanks for liquid oxygen will always come with detailed instructions for you to use. You want to be safe with your tanks for liquid oxygen, as well as making sure you do not waste any oxygen when you inhale oxygen from of tanks for liquid oxygen. Thin Film Deposition

    ReplyDelete
  7. thanks for sharing such an informative post.

    ReplyDelete